This SKU table contains a list of all SKUs available for the product. You can filter the list of items shown by selecting attributes.
Description
TacStar Shotgun Grips
Develop greater speed, accuracy, and control when shooting your 12 gauge shotgun with TacStar® Shotgun Grips. These injection molded, high impact, ABS polymer grips features the proper width, rearward angle and back swell to distribute recoil energy evenly into both hands for better shooting performance. Easy to install, the grips come with all the necessary hardware for installation and require no alterations to the shotgun. Forend and rear grips sold separately. 12 gauge only.
Forend and rear shotgun grips for better control and accuracy while shooting
Fit 12 gauge shotguns
Durable injection molded, high impact, ABS polymer construction
Front and rear grips distribute recoil energy evenly for better shooting performance
Comes with all necessary hardware for installation
Forend and rear grips sold separately
Web ID: 10228774
Reviews
Rated 4 out of
5 by
TheStig from
Pistol grips ftwGreat product..would buy again. Went on mossberg 500
Packaging says right on the front what it will fit and what it won't.
Date published: 2016-11-22
Rated 4 out of
5 by
TheStig from
Pistol grips ftwGreat product.. would buy again!
Date published: 2016-11-22
Rated 4 out of
5 by
Fishingnole from
Does the jobI purchased this pistol grip for a compact junior 20 Guage Remington 870. It took minor modification and a different screw to install it properly. Otherwise, it accomplishes what I desired it to do.
Date published: 2016-09-14
Rated 4 out of
5 by
babbelingbrook from
Good purchase but needed some work to fitAlthough most parts for the Remington 870 fit the H&R Pardner 12 ga. shotgun without alteration the TacStar Fore end pistol grip is an exception. However with a little work it can be made to fit. The grip is just a wee bit tight to fit onto the fore end slide tube. Solution: 1. use a drill with an extension and attach a sanding barrel or wire brush. Sand evenly till it slides onto the tube. 2. use a dremel with a cutting wheel and cut the barrel indentation on the grip about 3/4 to the fore end. The grip should slide on using a few blows with a hammer. I did #2 and grip works fine.
Date published: 2016-01-10
Rated 5 out of
5 by
Badax from
Good FitThis grip fits Mossberg 500 and Maverick 88 perfectly.
Easy install with a phillips and a long shaft flat large head screw driver. Does not work on 500 or 590 flex.
Date published: 2015-02-18
Rated 3 out of
5 by
wcfatcat from
need to be worked onfile top back as it hits barrel
Date published: 2015-01-13
Rated 5 out of
5 by
2trees from
Good but over pricedI was impressed how easily the forend installs the grip is great however found it over priced paid ne'er $40.00 & later found it available & cheaper than dirt for $26.00
Date published: 2013-06-12
Rated 5 out of
5 by
Walter40 from
Another great product from Cabela'sFit like a charm. No problems. Have Mossberg 500A, overe20 years old and replacement was easy. Although, you will need a very long screwdriver to remove the wooden stock.
Will the front grip fit a 2015 Mossberg 500 persuader?
The reason that I am asking is because I found one on another website the said that it wouldn't fit 2009 or newer Mossbergs. Im assuming its just an older model of this grip but I would like to be sure before I make a purchase. Im sold so long as it fits. Also it has a 7 round magazine tube if that makes a difference.
