Marksman Model 2070 Break Barrel Air Rifle Combo

The Marksman Model 2070 Air Rifle Combo Product Dimensions are: 45 x 7 x 3 inches ; 7.6 pounds and Shipping Weight is: 7.8 pounds.

The current price for the Marksman Model 2070 Air Rifle Combo is $69.99.

Mounting and Using Your Air Rifle Scope Mounting and Using Your Air Rifle Scope 1. Loosen eye piece locking ring and point scope toward a well lighted area without detail, such as a wall. CAUTION: DO NOT LOOK AT SUN WITH SCOPE AS PERMANENT EYE DAMAGE CAN BE RESULTED. Rotate eye piece left or right as needed until reticle appears sharp and clear to you, then retighten the locking ring. You will not have to make this adjustment again. 2. Loosen mount clamp screws, and slide the mounts into dovetail grooves on receiver of your air rifle. 3. Move scope forward or backward until eye piece position is most comfortable for you when rifle is held in shooting position. This distance is most commonly 3” from eye. Tighten clamp screws. 4. If reticle appears tilted, loosen scope clamp screws and rotate scope until reticle is perpendicular. Retighten clamp screws. 5. ZEROING: If pellet did not strike the point of aim, remove the windage and elevation caps, turn the dials in the direction needed to bring your next shot group to your point of aim. Turning the elevation dial in the direction of the arrow raises the point of impact; Turning the windage dial in the direction of the arrow moves the impact left. Mounting Your Scope The first step in mounting your scope is to remove the top half of the ring from the two-piece mount supplied. Then loosen the mount base screws and position the rings on the air rifle. The rear ring should be placed against the scope stop installed on the air rifle. The front ring will go near the front of the dovetail. The mount screws should be tightened just enough to hold them in place while the final adjustments are being made. Place the scope in the rings with the windage adjustment to the right side of the air rifle and attach the top half of the rear ring. WARNING: IF THE SCOPE IS NOT MOUNTED FAR ENOUGH FORWARD IN THE RINGS, ITS REARWARD MOTION MAY INJURE THE SHOOTER WHEN THE RIFLE RECOILS. AVERAGE DISTANCE FROM EYE SHOULD BE 3 INCHES. The screws should be tightened just enough to hold the scope from falling off. Next, shoulder the air rifle and look through the scope. Move the scope forward or rearward to get proper eye relief. This is when the view through the scope is the full view of the objective lens. The front ring should be adjusted so that it is centered in the front portion of the tube. Install the top half of the front ring and screws, but do not tighten them. Now that you have the position set you can tighten the bottom mount screws to the receiver. DO NOT OVERTIGHTEN or you will strip the threads. The final step is to align the cross hairs so they are level. The best way to do this is using a pair of small levels. With the air rifle placed securely on sandbags, place one level on the rear of the breech block and the other on the top of the elevation cap on the scope. Tighten the screws for the top half of the ring, alternating from side to side and watching the bubbles on the levels to ensure they are the same. Continue to tighten the screws until the tube is firmly clamped. DO NOT OVERTIGHTEN, or you will strip the threads and crush the tube.

Thank you for choosing Bass Pro Shops. You will have to check with your local 4 H to see what they allow for the competition.

Thank you for choosing Bass Pro Shops. This is a break barrel air rifle and does not take CO2.

Thank you for your question. According to the manufacturer this cannot be dry fired because the model 2070 has a rifled steel barrel and when you dry fire it will damage the riffling in the barrel.

Thank you for your inquiry: According to the manufacture: The recommended pellet for model 2070 is the Beeman pointed pellet model # 1239