This SKU table contains a list of all SKUs available for the product. You can filter the list of items shown by selecting attributes.
Description
Reviews
Q&A
Bass Pro Shops® rollers are made of a durable molded polymer blend and are non-marring, so you can snug your boat down on the trailer. Unaffected by oil, gas or salt. UV protected.
Durable molded polymer blend rollers
Non-marring
Impervious to oil, gas or salt
Web ID: 44932
Rated 5 out of
5 by
SalvelinusFontinalis from
Perfect replacementI replaced my old rubber rollers with these poly rollers. Installation was simple and my boat glides onto the trailer like wet ice on wet ice! Good product.
Date published: 2015-07-07
Rated 5 out of
5 by
boatman62 from
no more stripped off bow rollersI am very well pleased with my new super poly bow roller. I rolls easily when he bow of the boat touches It and allows the bow to slowly roll up to strap hook without damaging the bow pedestal or the roller. NO MORE TORN OFF BOW ROLLERS!
Date published: 2015-06-15
Rated 5 out of
5 by
Murph15 from
Great productWorks great. It don't leave any scuff marks on my boat
Date published: 2013-08-06
Rated 1 out of
5 by
TruckMan from
Sent the wrong rollerI ordered this for my Nitro boat. Won't fit...too small. No hardware provided. bass pro has slid so far downhill in the last 3 years. had to return...only cost $6.85 to return. what a bargain.
Date published: 2013-06-21
Rated 5 out of
5 by
slowisbetter37 from
non-marringWhat a plesure using a bow roller I don't have to scrub the black off the bow anymore. Strong & easy to install.
Date published: 2012-12-24
Rated 5 out of
5 by
Esox678 from
Poly RollersMuch better than the black rubber rollers. More stable and will not leave black marks on your keel.
They also roll better which makes loading and un loading much easier.
Date published: 2010-09-02
Rated 5 out of
5 by
MadMatt61 from
Good rollersEasy to install, Boat rolls well,looks good and most importantly it does not scuff my boat. Guess it does every thing they say it will so it's worth the few extra bucks.
Date published: 2008-06-11
Rated 1 out of
5 by
ByFly from
3" Super Bow roller (three pieces)I was very disapointed in this product item. After purchasing the 3 piece bow roller product. A 25 mile round trip to purchase it. And the work of moving the boat while on the trailer, all in order to remove my previous plain bow stop to make an improvement. What do I get for my trouble? A product that is provided with a through bolt that is to short to hold it all together after attempting installation. The bolt was not even long enough to reach the nylon keeper portion of the lock nut. The manufacturer doesn't take in account the trailer arm forks dimension that adds 1/2 inch to the total width of the final assembly. All the others in the store rack had this same length bolt, which appears to be long enough until installation time. I had to make a trip to the local Home Depot for a longer bolt. I didn't buy another nylok nut, trusting the nut from the set would fit. Bad move! It didn't, it was metric. Luckily, I had a S/S nylok nut that would fit the galvanized bolt I purchased. Now I was OK. The set-up was now on the trailer. I winched the boat up to the roller and saw that the roller outside pieces would distort and obviously take a set. I contacted someone that knows about the make-up of rollers and found that these are basically plastic rollers and have no UV protection. They will stick to the hull after a time out in the Sun and become brittle. I'm leaving this product on as I keep the boat in the garage, and will see how things go. I would not buy this product line again!
im looking to replace a bunk bow stop on my 14ft. flat bottom jon boat trailer with a roller(type D), under the winch. will this work and how does it install?
Asked by: hoopdrop
Make sure you are not looking to replace a bow roller which is down low on the trailer. A bow stop is generally up by the winch. It is very easy to replace and even comes with a new bolt. You need to measure between the steel rails where your bow stop is and it needs to be either a 3" or 4".
Answered by: Cobia254
Date published: 2017-06-01
I have measured the rollers I need to replace, but can't find all the necessary info with the products. One is 8" long, with an 8 1/2 inch gap in the
mount. The other is 9 1/2 inches though, and there isn't one listed in the Stoltz rollers that wide. That might work though, but the mount gap is 10 1/4 and the pin is 13 1/2 inches. The thickness of the roller at the keel is about 2 1/2 inches, so the boat will rest on it. The hole for the pin is about 5/8 inch so that should fit. How is the pin secured...pin or something else? Not sure I'm making this clear, but just wnat to make sure they'll fit,
Asked by: Karch
that is just what i had to do on my trailer works very good for me.
Answered by: colmac
Date published: 2017-06-01
What is the mounting hole size? Come with hardware sleeve pin etc?
WARNING: Cancer and Reproductive Harm - 
