SE Sport™ High Performance Hydrofoil
Sale price:
Clearance price:
Starting at:
Sale starting at:
Clearance starting at:
Reg. price:
- Compact design
- Improves handling and maneuverability
- 1-pc. high-strength copolymer construction
These compact, streamlined, state-of-the-art SE Sport™ High Performance Hydrofoils will improve handling and give you better maneuverability with a smoother ride. The Hydrofoil's crescent-shaped surface quickly funnels water for more thrust-cutting planing time for the quickest hole shot. The SE Sport Hydrofoil also keeps your boat on a plane at lower speeds. Features 1-piece, high-strength copolymer construction and control tip design. Also features Turbo Trac to enhance thrust and control. For all outboards and stern drives 25 HP and larger except: Volov; Merc 50 Two-Stroke; Merc 40, 50, 60 Four-Stroke (but does fit BigFoot models); Merc Bravo II and III (but does fit those with 2 round anodes); Honda® 200, 225. SE 300 fits motors 40-350 HP. SE 200 fits motors 8-40 HP. Manufacturer's lifetime warranty.
SE Sport Hydrofoil Clip sold separately and can be found through item search at item number 38-532-074-00
Rated 4.6 out of 5 by 85
reviewers.
Rated 1 out of 5 by MCPO NOT THAT GOOD
I put this on a 90HP Merc 2 stroke 17' Bass Boat. It did get on plane quicker, but when I trimed out, it dumped water into the back of the boat. Additionally, when I throttled down it threw water into the back of the boat. Additionally, it felt a little unstable on tight turns. For the price, I think the Stingray works best. I've used both.
May 21, 2008
Rated 4 out of 5 by aspec404 Works well
I have a 50hp Johnson and this is a great addition. I have found better fuel mileage and once on plain I can run slower RPM's. This really helps when your trying to get all you can get out of your small outboard
April 18, 2008
Rated 5 out of 5 by MrWalleye54 WOW
Before I installed this on my new Mercury 115 Optimax, out of the hole was a little slow. Now I can get on plane a lot quicker, and the ride on choppy water is a LOT smother. Instillation is quick and easy with common tools. Turning also is more stable and tighter at higher speeds. Want more Performance? GET ONE FOR YOUR MOTOR!!!!!!
March 8, 2008
Rated 1 out of 5 by danial54 Would not fit
I purchased the product that is designed for a smaller engine. The Item didn't come close to meeting the drill specs on the motor of my 9.8 hp Nissan outboard. A better adjustment to drill the plate to is needed for my motor. Will have to try another mfgr.'s fin.
January 24, 2008
29 Questions | 66 Answers
Outdoor Answers
Get help about this item from fellow customers.
Ask your questions. Share your answers.
Expand All
Collapse AllDetails:
I bought one of these for my triton BB. I noticed that mounting service on my Merc has a slight upward slope where it needs to mount. Therefor it won't mount flush. Any ideas???
(read all my Q&A)
Answers
A:
Here is a link to the manufacturer web site for installation. If you were still having problem I would recommend contacting SE Sports by calling 940-686-9000. Thankshttp://www.sesport.com/Installation...
Details:
of hole slowly - will this help?Answers
A:
Yes, per SE Sport: Independent tests have shown the SE Sport to be the fastest foil on the market. Trailer Boats Magazine rates the SE Sport fastest in 0 to 30 and top end speed, and Bass and Walleye Boats Magazine rates SE Sport fastest in top end speed. Because of increased stability, speeds higher than the boat's regular top speed are sometimes experienced (as was recorded in the Bass and Walleye Boats test). A very slight drop or no loss in top speed is more likely.Thanks
Details:
I raised the motor up to the 3rd hole and that seemed to help some but it still seems like it digging down and really using a good bit a gas my prop is 13.75x 13Answers
A:
The best way to improve performance, reduce on-plane RPMS and save fuel – the SE Sport will pay for itself over and over.• FASTER STARTS / CUTS PLANE TIME IN HALF
• BLASTS OUT OF SHALLOW WATER
• DEFEATS CAVITATION AND PROP BLOW OUT
• STOPS PORPOISING
• CURVED SHAPE FOR MAXIMUM THRUST
• BUILT IN TRACKING / STABILITY CONTROL
• NARROW PROFILE
• NEW MOLDED IN DECAL
• EXCLUSIVE SITE GAUGE FOR A PERFECT FIT
• MADE IN THE USA WITH A LIFETIME WARRANTY
• OPTIONAL SPORT CLIP FOR DRILL-FREE MOUNT
Call 940-686-9000 / 800-201-9095
Thanks
Answers
Top 250 Contributor
A:
Yes it does, you should be able to adjust it to completely eliminate cavitation. This of course also depends on the condition of your hull and proper mounting height of the motor or drive.This adjustment that can be done that is not in the installation instructions is to make slight adjustments to the angle of the foil. I did this by adding a stainless flat washer or two between the foil and the cavitation plate. This is at the two front bolts that hold the foil to the plate. Longer stainless bolts may be needed to allow these bolts to properly thread through the locking portion of the nut without over tightening. That very small difference of the thickness of the washer can and will make big performance changes to your boat. Do not eliminate the soft flat washers that came with the foil and otherwise follow the mounting instructions that came with the foil.
I have fine turned the foil angle with great success on a 16' runabout 110 HP and on a 14' aluminum fishing boat 25 HP.
This is referring to a foil that is bolted to the plate without the use of the optional "clip" mounting adapter.
A:
Found this answer on the manufacturers web site that might help answer yours: http://www.sesport.com/Questions.as..."Will it help with prop cavitation?"
Yes. Prop cavitation/ventilation where the propeller takes in air on turns is damaging to your motor and lower unit. The crescent-shaped of the SE Sport helps to hold water more firmly around the prop than any other foil on the market.
Thanks
Answers
A:
Yes its just the right size for my 50hp johnson so should fit ur 60hp with ease.
A:
The SE300 fits :All sizes that have a cavitation plate larger than 5 inches wide, usually 40 horse power and up. Because the mounting holes on the SE Sport 300 are 4 inches apart, right to left (center to center), a 5 inch or smaller cavitation plate leaves less than ½ inch of metal from hole to the edge of the plate. The SE Sport 200 is recommended for cavitation plates 5 inches or less.
Thanks
Details:
I currently have the Stingray XPI Senior, Black #SR-XPI-1 which I need to replace. Can you tell me if the bolt holes line up in the same location as the Sport Marine Tech SE Sport 300 Hydrofoil f/35-350HP?Answers
Top 250 Contributor
A:
In most if not all situations NO. I bought a used 110 HP motor that had holes in it for a Stingray foil. As much as I hated to drill more holes in my motor. I had to for the mounting of the SE foil.This never caused problems later.
Instead of a foil the best sulution to the problems that a foil might solve is to use automatic trim tabs. The foils are best when you have a hull design that will not allow the installation of trim tabs.
A:
there is multiple bolt holes.Details:
I currently have the Stingray XPI Senior, Black #SR-XPI-1 which I need to replace. Can you tell me if the bolt holes line up in the same location as the Sport Marine Tech SE Sport 300 Hydrofoil f/35-350HP?Answers
A:
If your hole pattern is from a previously installed Stingray (trademark of Marine Dynamics, Inc.) or Hydro-tail (trademark of TH Marine Supplies, Inc.) the Sport will match this pattern..You may want to compare your hole pattern to ours on the installation page: http://www.sesport.com/Installation.... ThanksDetails:
I have a black classic stingray hydro foil and i want to replace it with this one,but i don't want to redrill new holes will this line up ?????Answers
A:
I had an older stingray classic myself, according to the mounting instructions, I moved the SE300 Hydrofoil ahead to where they suggested. The great thing about this product is that they give you easy to use template with instructions, I just followed them, drilled 4 more holes, my previous holes were covered up by the new hydrofoil, and everything worked great.Answers
A:
You would need to contact the manufacturer for your motor warranties, since each manufacturer may be different. ThanksQ:
2 answers
I have a 18' G3 with 115 Yamaha, and it gets real wobbly when I turn. Will a hydrofoil help?
Answers
A:
You should trim down just a bit on turns. Mine does the same thing even with the hydrofoilA:
ON my sons it made a big diffrence
Get help about this item from fellow customers.
Ask your questions. Share your answers.
29 Questions | 66 Answers
