Select the "Economy Shipping" option at checkout before entering promo code CELEBRATE. Some Exclusions Apply. Offer ends July 6, 2015.
Free Shipping applies to economy shipping only to US and Canadian addresses on all internet or phone merchandise orders. (Canadian orders will be charged a $3.50 brokerage fee, duty and tax.) Excludes gift cards, orders shipped outside of the US and Canada, expedited or additional shipping and hazardous, special fees. Shipping charges on previous orders will not be reimbursed.
You may also order by calling 1-800-BASS-PRO (1-800-227-7776). Give the phone representative key code L5JA.
Millions of polymeric SuperCells harness the kick, releasing its energy over a longer time. Remington® SuperCell™ Recoil Pads reduce recoil by up to 54%. Fits any wooden stocked shotgun compatible with the R3 recoil pad, such as the Remington 870 and 1100. Made in USA.
I purchased a 300 Remington Ultra Mag that came with one of these. Having fired many rounds at the range, the comfort this provided got my attention. I purchased one for my 870 shotgun. 100 rounds in a day usually had me looking for pain medication that night. After this was installed on my shotgun, 100 rounds on top of 25 rounds from my 300 RUM didn't even come close to bothering my shoulder. Didn't even feel like I had gone shooting the next day. it's about half the cost of most other comparable recoil pads, and will also save you a fortune on pain medication. If you own a Remington that will accept one of these, treat yourself to one.
December 15, 2009
870 Express wood stock
Just bought and attached this to my 870 Express (wood stock) - Great at taking the bite out of the shot. It screws on just fine but doesn't quite fit - just a little narrow and a little long but then again an 870 isn't a prom queen to begin will.
Final verdict - does the job but could fit better.
April 18, 2009
super duper cell
by wood they ment the semi fancy wood, basically wingmaster, 1100, or 1187 premier, anything the r3 pad would fit, i bought a new 20g 1187 premier with a r3 limbsaver pad on it after a Few shots the squishy substance was grabbing my shoulder and pinching it , like a suction cup ... i decided i could do better then that, so i got this pad and i must say what a difference ... it's like a pillow on your gun. makes my 20 gauge shoot like a baby, and better yet is how good it looks(remington logos on the side) i have had mine through briars even and for 20.00 dollars there is no beating this thing, i am putting one on my 870 next... this is a must for the kids and the ladies thanks bass pro and thank you remington!!
November 15, 2008
I bought the wood SuperCell for my 870 Express. Packages says it would fit wood stocks. Just like everyone else that posted. I am returning this one.
August 22, 2008
I have found that there are two sizes to fit the BDL wood stock model 700. One size is 4-7/8" in length and the other is 4-15/16" in length. So which one is this? BPS has no measurements on these recoil pads.
Please post the thickness and height of the end of your wooden stock (not including your present pad and I'll measure my pad to see how it matches up. Be advised that it'll most likely be 2 to 3 times the thickness of the stock butt pad so you may end up with a length of pull that is too long for you.
Q #1 -- Can Bass Pro please advise the actual Remington Part # for the "Synthetic" SuperCell recoil pad (BassPro item no. 38-888-753-00)? I want to confirm it is the same as Remington Part # F301519... [see photo; pad with "30159" on it is the SuperCell] Q #2 -- Aso, can anyone confirm whether the SuperCell pad for Synthetic stocks comes with screws and are they Remington Part # F202537 "R3 recoil pad screw - 1" Philips" - which are silver colored with a one-piece integral washer style head to properly secure each of the two shorter hard material tubes inside the SuperCell pad to the holes in the stock? Note: these are *different* screws than those which came with the black rubber factory-installed pad typically provided on synthetic Model 870 Express shotgun stocks; those screws are black, longer, and have smaller 'standard' style Philips woodscrew type heads - so they will fit the different style holes, etc. in the factory-installed pad... [see photos of two types of screws and of inside a synthetic stock]
Images for this Question
(click to see full-size image)
(Click anywhere inside this popup to close it)
factory pad (top); SuperCell 'synthetic' pad (bottom)
(Click anywhere inside this popup to close it)
factory pad screws (left); 'washer head' type silver screws for SuperCell pad (right)
I bought the supercell pad for my rem870 with synthetic shurshot stock. If fit perfectly. I can't remember whether it came with the screw or whether I used the original...but I didn't have to buy anything extra. I think that it just came with the correct screw.
We will not share your email address or the recipient's email
address. We make no use of the email address or information contained in
these greetings except to complete the service as you have requested.