Offshore Angler™ Stainless Steel Rod Holders
Sale price:
Clearance price:
Starting at:
Sale starting at:
Clearance starting at:
Reg. price:
- Watertight cap
- Stainless steel construction
- Full-length, protective rubber liner
These rod holders have a watertight cap and feature a 316 stainless steel construction for years of use in harsh saltwater environments. Full-length, protective rubber liner prolongs the life of your valuable tackle. Available in 15° and 30° angles. 9-1/2'' L x 1-7/8'' Diameter.
Rated 4.7 out of 5 by 11
reviewers.
Rated 5 out of 5 by g3skipper Great product at a fair price.
The product is what I wanted and Bass Pro had the best price and delivery was on time. I can say that I got what I paid for in time for fishing season.
February 20, 2013
Rated 4 out of 5 by don8400 Excellent price
These rod holders are of good quality for a reasonable price.
August 2, 2011
Rated 4 out of 5 by jiminparker Quality & Price value
The ss rod holders are the least expensive I have found anywhere. The quality is equal to, if not better than every ss rod holder I have checked out. A good value for the price. I had the rod holders sent to a different address where I would be visiting and when I arrived a few days later they were already there. Bass Pro was on it for me with standard shipping. Timing was everything as I was outfitting a new boat and ready to get on the water asap. I installed the 30 degree holders toward the rear 1/3 of the boat gunnels at a outfacing direction giving me holders that can be used for trolling and additionally as angled stand up.
April 20, 2011
Rated 5 out of 5 by GnarlMalone Good product
These flush mount rod holders appear to be good quality. They look nice and preform as they were intended to. They didn't come with mounting hardware or very detailed instructions, but a trip to the local hardware store and a quick YouTube search solved both of these problems. I used 5200 marine sealant to seal them up. Can't be these things for their price.
October 7, 2010
6 Questions | 10 Answers
Outdoor Answers
Get help about this item from fellow customers.
Ask your questions. Share your answers.
Expand All
Collapse All
(read all my Q&A)
Details:
I want the holders just to use as rod holders on my boat for going to spot to spot. I may also use them for very light trolling. What would work best, 30 or 15 degrees?Answers
A:
15 degree would probably work best for you as the main use is a rod holder with an option of trolling. I have the 30 degree holders and they angle a bit more.
A:
15 degree holders are better for transporting altho 0 degree are best for transporting. With the 15 you can troll and still have adequate angle to "Read" your lures action.A:
Either will work very well. You'll have to set the drag slightly lighter w/ the 15 then the 30, but both will work well.Answers
A:
They have an open bottom with stainless pin.A:
They are open with a pin.A:
open bottom w/stainless pin. Pins are also serviceable without removing rod holder. Pins are standard size and fit all my rod buts even on my custom rods.Answers
A:
Take the gasket that comes with them and position it where you want rod holder. Draw around the INSIDE of the gasket. Remove gasket and drill a 3/8" hole. Take a jigsaw and cut the hole (you may have to shave more of the hole near the froward part if you have thicker gunnels (w/30 degree holder). apply 4200 sealant under gasket and screw down. Then go fishing. Takes about 15-20 minutes to install. They will easily fit OEM openings.A:
If you don't have one already. Use a1 1/4 inch hole saw for origional hole. then use a dremel tool or file to elonggate the hole for the proper angle. drill 3 holes and use s/s metal screws. If used as gimbal mount for downriggers add metal plumbers tape attached to bottom of rod holder and lock it down to a solid mounting ..problem solved
Details:
If yes, is the gimbal pin welded?Is the rod holder stamped or cast 316 stainless?
Answers
A:
They are stamped. I have had mine on my Sportsfisherman for 3 yrs now and the chrome has not flaked or begun to pit yet. Gimbal pin is mushroomed wich I prefer because they are easy to chang out for special applications or repair. The whoe reason I replaced my originals...
A:
These are 316 stamped stainless steel and the gimbal pin is welded.1 of 1
Get help about this item from fellow customers.
Ask your questions. Share your answers.
6 Questions | 10 Answers
1 of 1
