CMC PT-35 Tilt and Trim
Sale price:
Clearance price:
Starting at:
Sale starting at:
Clearance starting at:
Reg. price:
- Designed for up to 35 hp motors
- Accommodates clamp-on or bolt-on motors without an adapter
- 11-1/2" wide with a 5-1/2" setback
- Weight: 24 lbs.
Customers have asked for a smaller version of the PT-130 and here it is! This is designed for 35 HP and smaller motors. This unit is 11-1/2" wide with 5-1/2" setback and only weighs 24 lbs. It utilizes the same hydraulic actuator and will accommodate clamp-on or bolt-on motors without an adapter. This saves you time and money!
Rated 4 out of 5Â by 12
reviewers.
Rated 5 out of 5Â by IMAGRINCH Great Product
Installed the PT-35 on My Alumacraft Fisherman 145 CS with Suzuki 25 HP 4-stroke a little over two years ago and it's performed flawlessly.The installation was easy and the instructions were clear.The 51/2" set back makes the boat & motor perform a lot better.The tilt&trim has saved my back(Suzuki 4-stroke 25HP are quite heavy,161#, and are not available with factory trim&tilt).The PT-35 has made my fishing & boating alot more enjoyable.
June 17, 2012
Rated 1 out of 5Â by jamesmitch72 total waste of money
Bought this in Feb 2012. Just put on boat last weekend. It worked great I had no problems until I went out to the boat 5 days later and the motor was all the way up and would not lower. I recharged the battery, checked fuse and did everything I could think of. I had to hit the reset switch which means its an electrical problem, so I started looking into that.My vacation starts tomorrow so this is just great.The actuator is burned up.I could smell it as soon as I took the screw out which you shouldnt do because of the warranty which will void the claim. I have not talked to Cook yet to see how they will handle this but I sure will in the morning!!!
May 23, 2012
Rated 5 out of 5Â by 7fingers A great piece of equipment
Just finished installing on a 16' tracker with a 25hp merc 2 cyl and it work terrific I would recommend this to anyone with a 35hp or less. Cannot say enough
April 29, 2012
Rated 5 out of 5Â by davenewbrunswick wonderful place to shop
i ordered this tilt and trim along with some other items for my john boat , every thing came as promised and on time . was very easy to install ( i read the instructions first ) maybe took an hr to install . i just wish they woulk send the stainless bolts with it .
September 15, 2011
8 Questions | 16 Answers
Outdoor Answers
Get help about this item from fellow customers.
Ask your questions. Share your answers.
 Expand All
 Collapse AllDetails:Â
I have a tiller handle 1983 25hp 2 stoke Mariner Sea-pro, that is on a 14 ft flat bottom wood boat, was wondering if this would be able to be used on a tiller handle.
(read all my Q&A)
Answers
A:Â
The following is from the manufacturer.The PT-35 will accommodate a tiller type motor. In fact most of the motors that go on the PT-35 are tiller motors.
The most important thing about mounting a motor to the PT-35 is the width requirements. We have made the PT-35 so small and compact, some motors are too small wide to fit on the PT-35. Please measure the width of the clamp feet (outside to outside measurement) and any bolts that mount the motor including the head of the bolts. If the measurement is 11" or less, that motor will fit. If the measurement is more than 11", you would have to go to the PT-130 which will accommodate any motor up to a 130 H.P.
Details:Â
I have tried all the different tilts holes on the motor. The top speed I get is 21 mph. Thank youAnswers
A:Â
The PT35 gives you a more stable ride, increases top end speed, more prop clearance and better fuel efficiency. In addition, you might check with CMC for technical assistance by calling 580-252-1699. Thankshttp://www.cook-mfg.net/contact.htm...
Details:Â
Will this work with a 2011 25 hp mecury 4 stroke 15 inch length, mounted on a 14 ft tracker v gude ? Thank you !Answers
A:Â
Yes, this item is rated for 35 H.P. and Smaller Motors. Manual: http://cook-mfg.net/PDFs/PT35%20Own...Thanks
Answers
A:Â
This is rated for 35 H.P. and Smaller Motors
A:Â
It works great for my 2006 Mercury 25hp 2 stroke. Can't see why it wouldn't work for your Yamaha.
A:Â
Designed for up to 35 hp motorsAnswers
A:Â
It most certainly will without a problem
A:Â
Accommodates Clamp-on or Bolt-on Motors Without the Need of an Adapter.Q:Â
3 answers
Do I need to order the up and down buttons and wiring harness or does it come with it ?
Answers
A:Â
Icluded in your PT-35 box:1. One hydraulic PT-35 unit.
2. One wire assembly with toggle switch.
3. One switch plate and rubber boot.
A:Â
Comes with it. I didn't use the switch provided as I wired it directly to my trim switch on my shifter.Answers
Details:Â
i own a yamaha 40 hp and the PT 130 is like a hundred dollars expensiver..!Answers
A:Â
This is rated for 35 H.P. and Smaller Motors1 of 1
Get help about this item from fellow customers.
Ask your questions. Share your answers.
8 Questions | 16 Answers
1 of 1
