Free Shipping on orders $99+ Use code SHIP99

Enter promo code 'SHIP99' in the "Enter Promotion Code" box at checkout

You may also order by calling 1-800-BASS-PRO (1-800-227-7776). Give the phone representative key code L4BF

Free Shipping on orders of $99 or more applies to standard shipping only to US and Canadian addresses on all internet or phone merchandise orders. (Canadian orders will be charged a $3.50 brokerage fee, duty and tax.) Excludes gift cards, orders shipped outside of the US and Canada, expedited or additional shipping and hazardous, special fees. Shipping charges on previous orders will not be reimbursed. Cannot be combined with other promotions or offers.

CMC PT-35 Tilt and Trim

   

Sale price: Clearance price: Starting at: Sale starting at: Clearance starting at: Reg. price:

Description
Model
Quantity Price & availability

PT-35 Tilt and Trim

52100

  • $594.99

  • SKU: 633947

  • In Stock
  • Include 3 Yr Premium Accident Protection Plan

  • Add to Cart

    Add to Wish List

  • Designed for up to 35 hp motors
  • Accommodates clamp-on or bolt-on motors without an adapter
  • 11-1/2" wide with a 5-1/2" setback
  • Weight: 24 lbs.
Customers have asked for a smaller version of the PT-130 and here it is! This is designed for 35 HP and smaller motors. This unit is 11-1/2" wide with 5-1/2" setback and only weighs 24 lbs. It utilizes the same hydraulic actuator and will accommodate clamp-on or bolt-on motors without an adapter. This saves you time and money!
Rated 3.9 out of 5 by 14 reviewers.
Rated 1 out of 5 by Nightmare to install!!! I bought this for my Tracker Grizzly & Mercury 4Stroke 25 HP motor. It took my son & me over 12 hours to install! Not designed for the Grizzly boat as it hits on all bolts on the braces. Bottom hole on motor is not down far enough; misses mounting block for motor so can't put bolt there.Top bolt holes need to be down at least 1/2 inch more because we almost drilled through transom brace. Directions never mentioned in-line fuse so looked for hours when the item didn't work. Finally found the blown fuse. In order to make it work on Grizzly, had to put 1/4 inch plate shim to make it come out far enough for the bolts. May 20, 2011
Rated 5 out of 5 by It works! Tested yesterday for the first time, it' s the solution for "out-of-the-hole" problems I had with my Tohatsu 25/35. The installation is simple and easy but the instructions are not 100% precise: I followed step by step the manual and now the motor is too high and I have to redrill the transom to lower it a pair of inches so BE CAREFUL during the installtion! Anyway a good product and very fast service by BPS, thank you. November 21, 2010
Rated 5 out of 5 by Very nice accessory Very nice unit! If you're a handy person, installation isn't a big deal. One word of advise, pay very close attention to make sure that you mount the unit at the proper height in relation to the top of your transom, FLUSH!!!. Other than that the unit works great! May 11, 2010
Rated 1 out of 5 by PT has been a poor performer for me I purchased this unit and had it installed about 2 years ago. It has been nothing but a headache for me. The lower bracket that holds the piston has broken 3 times. (The part is about $12 with the shipping about $16.) It takes about 2 hours and a hoist to replace it. The last time I spoke with the service parts person at CMC he accused me of runing over stuff and breaking it which is false. I feel the aluminum brackets are just too weak. I have a 25 Johnson which is smaller than what it is rated for. Good luck if you purchase a lemon like I did. I am giving up on the unit and just remounting the motor without a tilt. November 27, 2008
<<prev 2 3 4 next>>
8 Questions | 16 Answers

Outdoor Answers

Get help about this item from fellow customers.

Ask your questions. Share your answers.

 
 
Browse Q&A
 
 
Sort by
Details: 
I have a tiller handle 1983 25hp 2 stoke Mariner Sea-pro, that is on a 14 ft flat bottom wood boat, was wondering if this would be able to be used on a tiller handle.
2 years, 4 months ago
Answer this Question
0
0

Answers

Staff Answer
A: 
The following is from the manufacturer.

The PT-35 will accommodate a tiller type motor. In fact most of the motors that go on the PT-35 are tiller motors.

The most important thing about mounting a motor to the PT-35 is the width requirements. We have made the PT-35 so small and compact, some motors are too small wide to fit on the PT-35. Please measure the width of the clamp feet (outside to outside measurement) and any bolts that mount the motor including the head of the bolts. If the measurement is 11" or less, that motor will fit. If the measurement is more than 11", you would have to go to the PT-130 which will accommodate any motor up to a 130 H.P.
2 years, 1 month ago
by
 - Springfield, MO.
Read all my Q&A (read all my Q&A)
0
0
Details: 
I have tried all the different tilts holes on the motor. The top speed I get is 21 mph. Thank you
2 years, 5 months ago
by
 - Pittsburgh
Read all my Q&A (read all my Q&A)
Answer this Question
0
0

Answers

Staff Answer
A: 
The PT35 gives you a more stable ride, increases top end speed, more prop clearance and better fuel efficiency. In addition, you might check with CMC for technical assistance by calling 580-252-1699. Thanks

http://www.cook-mfg.net/contact.html
2 years, 5 months ago
by
 - Springfield, MO
Read all my Q&A (read all my Q&A)
0
0
 
Q: 
1 answer

25 hp mecury 4 stroke

Details: 
Will this work with a 2011 25 hp mecury 4 stroke 15 inch length, mounted on a 14 ft tracker v gude ? Thank you !
2 years, 8 months ago
by
 - Huntington beach
Read all my Q&A (read all my Q&A)
Answer this Question
0
0

Answers

Staff Answer
A: 
Yes, this item is rated for 35 H.P. and Smaller Motors. Manual: http://cook-mfg.net/PDFs/PT35%20Owners%20Manual.pdf
Thanks
2 years, 5 months ago
by
 - Springfield, MO
Read all my Q&A (read all my Q&A)
0
0
3 years, 7 months ago
Answer this Question
0
0

Answers

Staff Answer
A: 
This is rated for 35 H.P. and Smaller Motors

A: 
It works great for my 2006 Mercury 25hp 2 stroke. Can't see why it wouldn't work for your Yamaha.
3 years ago
by
 - Barrie Ontario Canada
Read all my Q&A (read all my Q&A)
0
0
Vote as Best Answer
Thanks for Voting

Staff Answer
A: 
Designed for up to 35 hp motors
3 years, 2 months ago
by
 - springfield, mo
Read all my Q&A (read all my Q&A)
0
0
Vote as Best Answer
Thanks for Voting
3 years, 8 months ago
Answer this Question
0
0

Answers

A: 
It most certainly will without a problem
2 years, 5 months ago
0
0
Vote as Best Answer
Thanks for Voting

Staff Answer
A: 
Accommodates Clamp-on or Bolt-on Motors Without the Need of an Adapter.

A: 
Mine is a tiller and it works and i have a ladder holder there to hold armstrong ladder - it works really well. I have 25 tiller
3 years ago
by
 - Gainesville FL
Read all my Q&A (read all my Q&A)
0
0
Vote as Best Answer
Thanks for Voting
3 years, 11 months ago
Answer this Question
0
0

Answers

Staff Answer
A: 
Icluded in your PT-35 box:
1. One hydraulic PT-35 unit.
2. One wire assembly with toggle switch.
3. One switch plate and rubber boot.

A: 
Comes with it. I didn't use the switch provided as I wired it directly to my trim switch on my shifter.
3 years ago
by
 - Barrie Ontario Canada
Read all my Q&A (read all my Q&A)
0
0
Vote as Best Answer
Thanks for Voting

A: 
It comes with all the wiring and controls and includes a circuit breaker.
3 years, 2 months ago
by
 - Union City, TN.
Read all my Q&A (read all my Q&A)
0
0
Vote as Best Answer
Thanks for Voting
4 years, 4 months ago
Answer this Question
0
0

Answers

A: 
Yes, I am using it on a 25hp. Johnson and it works great for me.
3 years, 2 months ago
by
 - Union City, TN.
Read all my Q&A (read all my Q&A)
0
0
Vote as Best Answer
Thanks for Voting

A: 
NO PROBLEM!!!
4 years, 4 months ago
by
 - Endwell,NY
Read all my Q&A (read all my Q&A)
0
0
Vote as Best Answer
Thanks for Voting
Details: 
i own a yamaha 40 hp and the PT 130 is like a hundred dollars expensiver..!
5 years, 10 months ago
Answer this Question
0
0

Answers

Staff Answer
A: 
This is rated for 35 H.P. and Smaller Motors

A: 
Do your self a favor and buy the bigger unit. These things are designed very well, although I wouldn't recommend overloading them with a larger than recommended weight and thrust engine.
4 years, 4 months ago
by
 - Endwell,NY
Read all my Q&A (read all my Q&A)
0
0
Vote as Best Answer
Thanks for Voting
1 of 1
1 of 1

Need Help? 7 days a week: 7am to 10pm CT or call 1.800.227.7776 anytime