For a limited time: no oversize shipping charge on rods!
Select the "Economy Shipping" option at checkout.
Free Shipping on orders of $50 or more applies to economy shipping only to US and Canadian addresses on all internet or phone merchandise orders. (Canadian orders will be charged a $3.50 brokerage fee, duty and tax.) Excludes gift cards, orders shipped outside of the US and Canada, expedited or additional shipping and hazardous, special fees. Shipping charges on previous orders will not be reimbursed.
You may also order by calling 1-800-BASS-PRO (1-800-227-7776). Give the phone representative key code L5HA.
The Bass Pro Shops® Fuel Filter and Water Separator Kit increases fuel efficiency by removing water, dirt and other impurities from your fuel. The kit is designed for use with any 2- and 4-cycle outboard, inboard and inboard/outboard motors and includes a bracket and spin-on-style filter. When bracket and filter are put together, the height is 6.75". Filter has a 10 micron rating.
Increases fuel efficiency by removing water, dirt and other impurities
For use with any 2- and 4-cycle outboard, inboard and inboard/outboard motors
Includes a bracket and spin-on-style filter
Replacement filter cartridges for the Fuel Filter and Water Separator Kit are also available.
I put it on just before I went to Canada because Ive had issues before with water in gas while in Canada, seemed to work perfectly until I took my lower unit off from hitting a big rock.
June 23, 2011
I purchased this filter kit at the Bass Pro Shop Store in Orlando Fl. This filter system was everything I wanted for my 21ft Pontoon boat. It was easy to install in the motor mount well in front of the SUZUKI 90 hp motor. It was so easy to install, I used 3 stainless bolts to mount it. Being there, it is easy to change the filter any time. You need to purchase 1/4 mpt thread w/ proper slip or threaded fitting for your fuel line. Just follow directions. The hardest part was selecting the right place to mount the filter holder, and ease of changing the filter when needed
June 18, 2011
Works with modification
I purchased this unit because of its low price. I guess you get what you pay for.
I have an outboard motor and the filter didn’t come with any fittings for rubber hoses. So they had to be purchased along with clamps. After installing the unit I found that fuel wouldn’t flow into the filter and I had to drill out the intake to the filter before it would draw any fuel from the gas tank. It apparently had gunk in it. I’m hoping I’m the only person with this problem.
May 4, 2011
Have been concerned about water in gas supply from time to time.
Adding the filter provides peace of mind!
The installation is easy, just have to obtain the correct size fittings for the gas line and bolts and nuts to mount.
March 23, 2011
I changed mine once a year. My Lake Erie boat had water in the gas when I bought it and I put a fuel-water mixer I bought at a marina which blended the water into the gas and I had no more problem with it after that, so then I put a seperator kit on it. My tank was 53 gallon and made of aluminum.
No, when the filter is full it is disposed of and you replace the filter much like you do when you have an oil change on your vehicle. They do make filters with a water drain off but, it has been my experience that they are made of a cheap plastic and they brake really easy. This happens with very little pressure and something as simple as a battery jumping could smash that filter leaving you stranded. Stick with this type of filter, you won't be disappointed.
First locate your fuel line. Then search for a good mounting surface that is not to close to anything electrical ( wiring or batteries) remember to never use any part of the boats hull for mounting because you could create an unnecessary hole. After locating your mounting area, make sure your fuel line will reach there. Clean the area thoroughly and mount the filter system. Next, run the fuel line up to the fuel intake portion of the filter and slide it on to the brass fitting and tighten down the hose clamp. On, the opposite side of the filter is the fuel flow out fitting slide the new hose on to the fitting and secure it with the hose clamp. The final step is to take the other end of the hose and fit it on to the intake fitting where the pump ball is to supply fuel to the engine. Prime the ball until it is solid and be patient. She will have a little trouble starting at first because, of all the air in the line. When the air is removed and the supply ball is pumped up solid you should now be all set. NOTE* Most filters do not come with the brass fittings. You need to know the size of your fuel line hose in order to purchase these. You will also need to measure the fuel out line length and purchase that length of fuel hose to complete this project.
We will not share your email address or the recipient's email
address. We make no use of the email address or information contained in
these greetings except to complete the service as you have requested.