Select the "Economy Shipping" option at checkout before entering promo code CELEBRATE. Some Exclusions Apply. Offer ends July 6, 2015.
Free Shipping applies to economy shipping only to US and Canadian addresses on all internet or phone merchandise orders. (Canadian orders will be charged a $3.50 brokerage fee, duty and tax.) Excludes gift cards, orders shipped outside of the US and Canada, expedited or additional shipping and hazardous, special fees. Shipping charges on previous orders will not be reimbursed.
You may also order by calling 1-800-BASS-PRO (1-800-227-7776). Give the phone representative key code L5JA.
The Bass Pro Shops® Canoe Motor Mount gives you the versatility of motor power from your favorite canoe. This easy-installing mount allows you to use a gas or electric motor with your canoe, so you can get to that great fishing spot faster and start fishing without delay. This durable aluminum and hardwood mount allows you to attach a gas or electric motor up to 3 HP directly to your canoe. Oversized, easy grip tightening knobs makes mounting quick and easy without needing any tools. Heavy-duty clamps attach mount surely and securely to the gunwales of your canoe. Weight: 2.81 lbs.
Manufacturer model #: FM2003-014445.
Mount gas or electric motor to your canoe
Easy to install bracket
Heavy duty aluminum and hardwood construction
Accommodates motors up to 3 HP
Handtightens to the gunwales of your canoe - no wrenches
Very well made
I purchased the motor mount to use on 2 different canoes , one with plastic gunwales the other is wood.Easy on easy off. Adjustable and very solidly built. I would recommend this to anyone!
October 18, 2010
An outstanding product, a good solid mount for trolling motor. My 27# can turn 360, the prop clears the canoe.
October 8, 2010
Canoe Motor mount
So far, so good. Mount installs easily to my "Old Town" canoe. And my Minn-Kota 34 pounl thrust motor fits perfectly. I tried not to tighten the clamps to the gun whales to much at first and as a result - the mount came lose after awhile. So I tightened it some more and no further problems.
My wife and I enjoyed a good 2 plus hours fishing.
September 30, 2010
Just so so
The canoe motor mount performed its function, however I found the following when using a 45 lb trust electric motor on it:
- Had to periodically check the tighting knobs as came loose a couple of times in use.
- the mount would flex more than I would have liked it to when the motor was in high.
September 29, 2010
I'm guessing yes, but does anyone know for sure? Can you mount the bracket so the motor can go on either the left or right side? Being right-handed, I think I would want to have the motor on my right, not on the left as it would be as shown in the photo on the website.
I have a brand new long shaft, Honda 2HP outboard mounted on my 16 ft. Fiberglass Old Town Katahdin. The mounting bracket I am using is the Old Town bracket sold here. My problem is, when I go at a little faster rate of speed the engine shaft is causing a "wake" that then goes up the wall of the canoe and over the gunnel. The engine only weighs 26 lbs and my boat has a fairly flat bottom and sits high out of the water. How can I prevent this?
Same problem with my 2.5hp yamaha on 18' Grumman. Answer was simple. a piece of thin pliable plastic such as that from a 5 gal pail, cut to fit a 2ft long spray shield and attached with duct tape. worked like a charm.
Why not just attach the motor to the transom of your rowboat? The boat is most certainly set up for that purpose. Unless you mount the bracket far forward, you would not be able to span from gunwale to gunwale, necessary for stability. Would not seem like that would be a productive place from which to drive the craft.
We will not share your email address or the recipient's email
address. We make no use of the email address or information contained in
these greetings except to complete the service as you have requested.