For a limited time: no oversize shipping charge on rods!
Select the "Economy Shipping" option at checkout.
Free Shipping on orders of $50 or more applies to economy shipping only to US and Canadian addresses on all internet or phone merchandise orders. (Canadian orders will be charged a $3.50 brokerage fee, duty and tax.) Excludes gift cards, orders shipped outside of the US and Canada, expedited or additional shipping and hazardous, special fees. Shipping charges on previous orders will not be reimbursed.
You may also order by calling 1-800-BASS-PRO (1-800-227-7776). Give the phone representative key code L5HA.
The Bass Pro Shops® Canoe Motor Mount gives you the versatility of motor power from your favorite canoe. This easy-installing mount allows you to use a gas or electric motor with your canoe, so you can get to that great fishing spot faster and start fishing without delay. This durable aluminum and hardwood mount allows you to attach a gas or electric motor up to 3 HP directly to your canoe. Oversized, easy grip tightening knobs makes mounting quick and easy without needing any tools. Heavy-duty clamps attach mount surely and securely to the gunwales of your canoe. Weight: 2.81 lbs.
Manufacturer model #: FM2003-014445.
Mount gas or electric motor to your canoe
Easy to install bracket
Heavy duty aluminum and hardwood construction
Accommodates motors up to 3 HP
Handtightens to the gunwales of your canoe - no wrenches
Canoe motor mount
The mount fit my Old Town 158 Canoe great. The mount is stury enough for my 54lb. thrust trolling motor. I have always trusted Bass Pro (BP) for all my fishing needs. So why not buy the mount also. It came in a timely manore and a resonable price. When it came I installed it and low and behold. "MADE IN CHINA" Really!!!! Can't Bass Pro find an American made stuff as simple as a canoe mount? If I had know it was made in China I wouldn't have purchased it. I am just a little PO'd. I am going to question my purchased from BP for now on. BP wants Americans to buy thier products so why don't they buy American?????
May 13, 2012
If it will fit my old Golden Eagle 14' fiberglass,
it will fit anything.
Appears well made,,,time will tell.
Now for a camo paint job and I'd be ready for the river.
April 11, 2012
Not Compatible with Coleman Tram X Canoes
This item will not work with Coleman Tram X canoes that have the square stern. It is too short.
April 8, 2012
I used this mount on my Old Town Canoe w/55# thrust electric motor with no problem all last season. Quick on off with the hand screws makes this a very convenient accessory.
March 2, 2012
I'm guessing yes, but does anyone know for sure? Can you mount the bracket so the motor can go on either the left or right side? Being right-handed, I think I would want to have the motor on my right, not on the left as it would be as shown in the photo on the website.
I have a brand new long shaft, Honda 2HP outboard mounted on my 16 ft. Fiberglass Old Town Katahdin. The mounting bracket I am using is the Old Town bracket sold here. My problem is, when I go at a little faster rate of speed the engine shaft is causing a "wake" that then goes up the wall of the canoe and over the gunnel. The engine only weighs 26 lbs and my boat has a fairly flat bottom and sits high out of the water. How can I prevent this?
Same problem with my 2.5hp yamaha on 18' Grumman. Answer was simple. a piece of thin pliable plastic such as that from a 5 gal pail, cut to fit a 2ft long spray shield and attached with duct tape. worked like a charm.
Why not just attach the motor to the transom of your rowboat? The boat is most certainly set up for that purpose. Unless you mount the bracket far forward, you would not be able to span from gunwale to gunwale, necessary for stability. Would not seem like that would be a productive place from which to drive the craft.
We will not share your email address or the recipient's email
address. We make no use of the email address or information contained in
these greetings except to complete the service as you have requested.